SPXクロスヘッドベアリング スペアパーツ

SPX Crosshead Bearings – Guide and Alignment Bearings for SPX Flow Homogenisers

SPX crosshead bearings are essential mechanical components within the drive system of SPX Flow homogenisers. They guide and support the crosshead during reciprocating motion, ensuring accurate alignment between the crankshaft, connecting rod, and plunger rod. Bos Homogenisers supplies OEM-compatible SPX crosshead bearings designed for long service life, stable operation, and precise alignment under continuous high-load conditions.

Whether you are performing a complete overhaul or replacing worn guide components, our crosshead bearing solutions support both current and legacy SPX Flow homogenisers used in food, dairy, pharmaceutical, and industrial processing.

What Are SPX Crosshead Bearings?

SPX crosshead bearings are sliding or guide bearings installed within the crosshead assembly of the homogeniser drive end. Their primary function is to guide linear movement while absorbing side loads generated by the rotating crankshaft and connecting rod.

By maintaining correct alignment, crosshead bearings protect critical components such as plunger rods, seals, cylinder blocks, and frame assemblies.

Function of Crosshead Bearings in SPX Homogenisers

• Guide linear movement of the crosshead assembly
• Maintain alignment between crankshaft and plunger rod
• Absorb lateral and dynamic loads
• Reduce friction and mechanical vibration
• Protect frame and drive components from wear

Without properly functioning crosshead bearings, misalignment can quickly lead to seal failure, plunger damage, and excessive frame wear.

SPX Flow Crosshead Guide Bearings

SPX Flow crosshead guide bearings are precision-machined components that support the sliding movement of the crosshead within the frame. These guide bearings are designed to operate under continuous cyclic loads while maintaining tight dimensional tolerances.

Bos Homogenisers supplies guide bearings manufactured from materials selected for durability, low friction, and resistance to wear.

SPX Sliding Crosshead Bushing

The SPX sliding crosshead bushing acts as the bearing surface between the crosshead and guide rails or frame housing. It allows smooth sliding motion while preventing metal-to-metal contact.

Sliding bushings are typically made from bronze alloys, composite materials, or polymer-based compounds, depending on load conditions and lubrication method.

Crosshead Block Bearing SPX

The crosshead block bearing SPX is installed directly into the crosshead block or frame. It supports the crosshead body and maintains its position throughout the full stroke length.

Accurate machining of the crosshead block bearing ensures uniform load distribution and minimises localized wear on both the bearing and mating surfaces.

SPX Plunger Rod Guide Bearing

The SPX plunger rod guide bearing ensures that the plunger rod remains perfectly aligned as it transitions from rotary crank motion to linear pumping motion. This alignment is critical to protecting packing sets and guiding rings from uneven wear.

Worn plunger rod guide bearings often result in increased seal leakage and shortened service intervals.

Frame Drive Bearings SPX

Frame drive bearings SPX include crosshead bearings, guide bushings, and related components that support motion within the homogeniser frame. These bearings operate in combination with connecting rod bearings and crankshaft bearings to ensure smooth mechanical power transmission.

Regular inspection of frame drive bearings is essential to prevent vibration, noise, and progressive mechanical damage.

SPX Piston Crosshead Alignment

SPX piston crosshead alignment is achieved through the correct interaction of crosshead bearings, guide rails, and connecting rod geometry. Proper alignment ensures that axial forces are transmitted efficiently while minimizing side loads.

Misalignment can cause:

• Accelerated plunger and seal wear
• Increased friction and heat generation
• Premature failure of cylinder blocks and packings

Materials Used in SPX Crosshead Bearings

SPX crosshead bearings are manufactured from materials chosen for strength, wear resistance, and compatibility with lubrication systems:

• Bronze or bronze-based alloys
• Steel-backed composite bearings
• Polymer or PTFE-based sliding materials

Material selection depends on operating speed, load, lubrication method, and environmental conditions.

When Should SPX Crosshead Bearings Be Replaced?

Crosshead bearings are wear components and should be replaced when any of the following signs are observed:

• Increased vibration or knocking noises
• Uneven wear patterns on guide surfaces
• Excessive clearance or axial play
• Metal particles found during oil inspection

Timely replacement prevents damage to higher-cost components such as crankshafts and frames.

推奨メンテナンス間隔

Typical service guidelines include:

• Visual inspection during major overhauls
• Measurement of bearing clearances every 6,000–10,000 operating hours
• Replacement during scheduled frame service

Actual intervals depend on operating pressure, speed, and lubrication quality.

インストールのベストプラクティス

• Clean all mating surfaces thoroughly before installation
• Ensure correct bearing orientation and alignment
• Apply recommended lubrication during assembly
• Check smooth crosshead movement before startup

Correct installation is essential for achieving full bearing service life.

Compatible SPX Flow Homogeniser Models

Bos Homogenisers supplies SPX crosshead bearings for a wide range of machines, including:

• SPX Flow MC series homogenisers
• Rannie and Gaulin legacy machines
• シングルステージおよび2ステージホモジナイザー

Bearings are matched using machine model, serial number, and frame configuration.

スペアパーツを納入しているSPXマシン

Bos Homogenisers supplies spare parts for a broad SPX homogeniser range, including SPX Gaulin MC and G series, SPX R series machines and laboratory configurations. Share your SPX model and machine details so we can help identify the correct spare parts and ensure compatibility with your configuration.

Bosのホモジナイザーを選ぶ理由

Bos Homogenisers is a specialist supplier of aftermarket spare parts for SPX Flow homogenisers. Customers worldwide rely on us for:

• OEM-compatible SPX crosshead bearings
• 旧型および製造中止となった機種への対応
• 専門家による技術支援
• 迅速な世界配送

How to Order SPX Crosshead Bearings

1. Provide your SPX model and serial number
2. Confirm frame and crosshead configuration
3. 見積もりと納期を確認する
4. 欧州の倉庫からの世界中への発送

見積依頼

If you need SPX Flow crosshead guide bearings, a sliding crosshead bushing, or components to restore SPX piston crosshead alignment, Bos Homogenisers is your trusted partner for high-quality aftermarket parts.

メールアドレス：info@boshomogenisers.com

電話番号：+31 (0)123 456 789

Request a Quote for SPX Crosshead Bearings

関連するSPX用スペアパーツ

その他のSPXホモジナイザー用スペアパーツをお探しですか？当社のSPX交換用部品の全ラインナップをご覧ください：

• SPXコネクティングロッドベアリング – コネクティングロッドベアリング
• SPXシリンダーブロック – 高精度シリンダーブロック
• SPXオイルフィルター – 潤滑油フィルター
• SPX計装 – Gauges, sensors, and instruments
• SPX油圧システム – Hydraulic system components

View all SPX spare parts →

他社製の互換製品

Looking for crosshead bearings for other homogeniser brands? BOS Homogenisers supplies compatible replacements across all major brands:

ボスホモジナイザークロスヘッドベアリング | ラニークロスヘッドベアリング | APVクロスヘッド・ベアリング | ゴーリン・クロスヘッド・ベアリング

連絡先